Service Structured cabling & electrical

Cabling and power that everything else stands on

Cat6/6A and fibre, tested and labelled; extra-low-voltage runs kept clean of power; and electrical works, switchboards and UPS by licensed electricians — handed over with drawings that show what went where.

Discuss your projectHow we deliver

From drawings to as-builts — in 20 seconds

Drawings & programFrom your builderDesignRoutes · outlets · loadsRough-inCables in with the buildRough-inCables in with the buildFit-offOutlets · panels · UPSFit-offOutlets · panels · UPSTest & labelEvery run, results keptTest & labelEvery run, results keptBefore linings closeAll runs passAs-builts deliveredDrawings & test resultsSite ready for equipmentDelivered and documented by PI NETWORKRoutes, outlet positions and electrical loads are designed from the drawingsCamera, access-point and phone positions come from the systems designRough-in goes in with the build, before the linings closeData separated from power; conduits where the walls will beFit-off: outlets, patch panels, switchboard and UPSElectrical works by licensed electriciansEvery copper and fibre run is tested and labelledResults are kept with the documentationAs-built drawings handed over; the site is ready for equipmentThe same crew works to the design the network and cameras are built on
  1. DesignRoutes, outlets and loads from the drawings and the builder's program.
  2. Rough-inCabling and conduits installed before the ceilings and walls close.
  3. Fit-offOutlets, panels, switchboard and UPS fitted.
  4. TestEach run tested and labelled; results kept.
  5. Hand overAs-built drawings delivered; equipment can go in.
20-second walk-through. Replay any time.

Who it is for

Builders, tenants and owners who need the physical layer done once, by one crew, before the systems go in — and logistics operators whose sorting equipment needs dedicated power and data.

What we are usually called about

  • Patch panels that were never tested and outlets nobody labelled
  • Data pulled alongside power by whoever was cheapest that week
  • A switchboard signed off by a contractor who has since disappeared
  • Cameras and access points planned after the ceilings were closed
  • Sorting or kitchen equipment that needs its own circuits and nobody allowed for them

What we provide

Structured cabling

Cat6/6A and fibre backbone and horizontal runs, patch panels and outlets, every run tested and the results kept.

Extra-low-voltage runs

Data, control and signalling cabling routed and separated from power so it performs as specified.

Electrical works

Circuits, switchboards and UPS for racks, sorting lines, kitchens and counters, by licensed electricians.

Power and data for automation

Dedicated supply and data for conveyors and sorters, installed to the equipment supplier's requirements.

As-built documentation

Labelled drawings and a record of exactly what was installed, where, handed to you and kept on file for support.

Coordination with the build

We sequence with your builder and other trades so the cabling is in before the ceilings close and the comms room is ready for equipment.

What shapes the solution

What we confirm before quoting:

  • Drawings and the program. Floor plans, ceiling types and the builder's schedule decide routes and timing.
  • What the cabling serves. Camera, access point and phone positions are planned from the systems design, not guessed.
  • Electrical load. Rack, kitchen and equipment loads set circuits, switchboard capacity and UPS sizing.
  • Existing infrastructure. Reusable risers, trays and runs are tested before we rely on them.
  • Site access and permits. Landlord approvals, after-hours access and any electrical permits are arranged up front.

How we deliver — or take over

Survey and design

Routes, outlet positions and loads confirmed on site and on drawings.

Rough-in

Cabling and conduits installed with the build, before linings close.

Fit-off and test

Outlets, panels and switchboards fitted; every run tested and labelled.

Hand over

As-built drawings and test results delivered; the site is ready for equipment.

Taking over an existing setup

On an existing site we test what is there, label what passes and re-run what does not, then give you the drawings the previous installer never did. Electrical defects found during the audit are reported with a quote rather than quietly worked around.

Related project

Warehousing & logisticsMulti-state

YTO Express Australia — a national parcel network on one platform

Cloud call centre plus the networking, Wi-Fi, CCTV, certified cabling and electrical works behind each depot and sorting hub, delivered as one project and supported day to day.

Read the case study →

Common questions

Is the work tested and certified?
Every copper and fibre run is tested and the results are kept with the as-built documentation. Electrical works are carried out and certified by licensed electricians.
Do you do both the data and the electrical?
Yes, under one project with one party accountable, so there is no gap between trades.
Can you handle power for sorting lines or conveyors?
Yes. We install the dedicated distribution, switchboards and UPS that automated equipment needs, to the supplier's requirements.
Does it tie in with the rest of our systems?
That is the point of doing it with us: the crew that pulls the cabling works to the same design as the network, cameras and phones going on top of it.

Discuss your project

Tell us the site, what has to work and when. An engineer will come back to you within one business day.

Discuss your project